petoi-camp-logo.png
Chinese
ZH
Chinese
ZH
English
EN
  • 主页

  • 论坛

  • Shop

  • 简介

  • 图鉴

  • 资源

    • Documentation Center
    • GitHub 源代码
    • 教程视频
    • NyBoard V0_1 手册
    • NyBoard V0_2 手册
    • Smartphone App
    • GitHub/CatMini
  • 社区

    • 成员
  • More

    Use tab to navigate through the menu items.
    Hanna Ovr
    8月02日

    Pest Control Software

    2
    0
    Rafael Marín
    vor 3 Tagen

    Error moving joints simultaneously in Mobile app

    5
    0
    Tomi Ade
    vor 6 Tagen

    Trouble Uploading to Nyboard - stk500_recv(): programmer is not responding

    3
    0
    若要查看作用方式,請前往您的即時網站。
    • 類別
    • 所有文章
    • 我的文章
    Stuart Keen
    5月28日

    Board Configuration Problems

    在 General Discussions

    Hi, Just assembled Bittle up to paragraph #4 Board Configure. I downloaded the apps

    1. Arduino - when opened, headline reads “sketch_may27d | Arduino 1.8.19.”

    2. OpenCat.ino - when opened headline reads “OpenCat | Arduino 1.8.19”


    If I read correctly, I skip paragraphs 4.2.1 and 4.2.2 (bracketed with brown line).


    Paragraph 4.2.3 shows Arduino file opened with headline reading “Arduino File Edit Sketch Tools Help”.

    How do I get there. What file(s) am I missing?


    Searching the Forum, YouTube videos etc has not helped so basically “stuck” at paragraph 4.2.3. Any help would be appreciated. I have basically no programming experience. My desktop is an iMac.


    17 則留言
    0
    17 則留言
    S
    Stuart Keen
    5月28日

    I was gone from my computer for past three hours, therefore Lark access codes expired. Please send again. Thanx.

    按讚
    R
    Rongzhong Li
    5月29日
    回覆

    I updated the access permission. You may try it again. https://tn2lsjcal7.larksuite.com/drive/folder/fldusANNJtuYuZmpAfOZVlHvcKN

    按讚

    S
    Stuart Keen
    5月28日

    Lark won't allow me to download the driver. They say I must request permission from you. I have added you to my Contact file.


    按讚

    R
    Rongzhong Li
    5月28日

    Have you connected the green USB programmer to your mac? After that, you should be able to see a new port. If not, you may need to install the driver: https://tn2lsjcal7.larksuite.com/drive/folder/fldusANNJtuYuZmpAfOZVlHvcKN And you can find the lines of code in OpenCat/WriteInstinct/OpenCat.h.

    按讚

    S
    Stuart Keen
    5月28日

    I have the Bittle connected to my Mac’s USB port. RED LED on USB Uploader board, BLUE LED on the NyBoard. Under Arduino “Tools” menu, mine is reading different than shown in figure in 4.2.3. Perhaps a newer version?


    1. I am able to select “Arduino Uno”, just don’t have the intermediate step (don’t have choice Arduino AVR Boards or NyBoard-avr) as shown in paragraph 4.23. I assume this is OK. See my Fig 1.


    2. However, how do I select a new port? I only have ports for iPad and Bluetooth showing. Do I add in preference? If so, how? Fig 2, 3 & 4.


    I opened OpenCat and found only (Fig 5)

    #ifdef BITTLE

    PTLF("Bittle”);


    Thank you again so much for taking time to get me started on this project.