petoi-camp-logo.png
Chinese
ZH
Chinese
ZH
English
EN
  • 主页

  • 论坛

  • Shop

  • 简介

  • 图鉴

  • 资源

    • Documentation Center
    • GitHub 源代码
    • 教程视频
    • NyBoard V0_1 手册
    • NyBoard V0_2 手册
    • Smartphone App
    • GitHub/CatMini
  • 社区

    • 成员
  • More

    Use tab to navigate through the menu items.
    Rafael Marín
    -2 j

    Error moving joints simultaneously in Mobile app

    5
    0
    Tomi Ade
    -5 j

    Trouble Uploading to Nyboard - stk500_recv(): programmer is not responding

    3
    0
    Phillip Brush
    8月09日

    On Definition Rule Issues

    4
    0
    若要查看作用方式,請前往您的即時網站。
    • 類別
    • 所有文章
    • 我的文章
    Omar Samy
    2021年4月30日
    已編輯: 2021年4月30日

    CAN'T FIND THE PORT OF THE FTDI UPLOADER ?

    在 General Discussions

    In file included from sketch\OpenCat.h:85:0,

    from D:\project data\2021\GEN CODE\OpenCat\WriteInstinct\WriteInstinct.ino:2:

    C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.42.0_x86__mdqgnx93n4wtt\hardware\arduino\avr\libraries\Wire\src/Wire.h: In member function 'void Motion::loadDataFromI2cEeprom(unsigned int&)':

    C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.42.0_x86__mdqgnx93n4wtt\hardware\arduino\avr\libraries\Wire\src/Wire.h:68:13: note: candidate 1: uint8_t TwoWire::requestFrom(int, int)

    uint8_t requestFrom(int, int);

    ^~~~~~~~~~~

    C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.42.0_x86__mdqgnx93n4wtt\hardware\arduino\avr\libraries\Wire\src/Wire.h:65:13: note: candidate 2: uint8_t TwoWire::requestFrom(uint8_t, uint8_t)

    uint8_t requestFrom(uint8_t, uint8_t);

    ^~~~~~~~~~~

    Sketch uses 24946 bytes (77%) of program storage space. Maximum is 32256 bytes.

    Global variables use 1380 bytes (67%) of dynamic memory, leaving 668 bytes for local variables. Maximum is 2048 bytes.


    -- consdering that i installed the ch341ser and configerd the FTDI uploader manully in the device maneger and the only port i get is "COM3"

    nyboard v1_0

    14 則答覆0 則回覆
    0
    14 則留言
    John Winiger
    2021年4月30日

    yes, it takes a little while, and I have mentioned to other I find it best to lift all the feet off the ground, then calibrate the legs and then go back to the feet. So probably c12 -7 c13 -7 c14 -7 c15 -7. and then when everything is calibrated remember to send an "S" to save the calibration.

    2

    O
    Omar Samy
    2021年4月30日

    now it's calibrating the MPU is it ok that it's long time to calibrate it ?

    1
    R
    Rongzhong Li
    2021年5月01日
    回覆

    Is the I2C switch dialed to Arduino?

    按讚

    O
    Omar Samy
    2021年5月01日
    回覆

    @Rongzhong Li yes that was the problem of some other small problems I figured it out thanks to john but what really confuse me now the servo joints wiring and I'M connecting them now based on this doc because it's v1_0 board and i'm not sure it's the right connections

    the nyboard defined as v1_0 in the code


    按讚

    R
    Rongzhong Li
    2021年5月02日
    回覆

    @Omar Samy The wiring locations are the same for all NyBoard versions. Only the physical location matters.

    按讚

    John Winiger
    2021年4月30日